Arduino Nano ESP32 - DHT22

This tutorial provides instructions on how to use Arduino Nano ESP32 to read temperature and humidity value from DHT22 sensor, and print it to Serial Monitor. The tutorial provide instructions for both DHT22 sensor and DHT22 module.

Hardware Preparation

1	×	Arduino Nano ESP32
1	×	USB Cable Type-C
1	×	DHT22 Temperature Humidity Sensor Module
1	×	10 kΩ resistor
1	×	Breadboard
1	×	Jumper Wires
1	×	(Optional) DC Power Jack
1	×	(Recommended) Screw Terminal Expansion Board for Arduino Nano
1	×	(Recommended) Breakout Expansion Board for Arduino Nano
1	×	(Recommended) Power Splitter For Arduino Nano ESP32

Or you can buy the following sensor kits:

1	×	DIYables Sensor Kit (30 sensors/displays)
1	×	DIYables Sensor Kit (18 sensors/displays)

Disclosure: Some of the links provided in this section are Amazon affiliate links. We may receive a commission for any purchases made through these links at no additional cost to you.
Additionally, some of these links are for products from our own brand, DIYables.

Overview of DHT22 Temperature and Humidity Sensor

	DHT22
Operating Voltage	3 to 5V
The humidity range	0% to 100%
The humidity accuracy	± 2% to 5%
The temperature range	-40°C to 80°C
The temperature accuracy	± 0.5°C
The reading rate	0.5Hz (one time per 2 seconds)

DHT22 Pinout

DHT22 has two form: raw sensor and module:

DHT22 sensor includes 4 pins:

GND pin: connect this pin to GND (0V)
VCC pin: connect this pin to VCC (3.3V or 5V)
DATA pin: the pin is used to communicate between the sensor and Arduino Nano ESP32
NC pin: Not connected

We highily recommend you using DHT22 module. The modules have a built-in resistor and have only three pin: VCC, GND, and DATA pins (or alternatively: +, -, and OUT pins).

Wiring Diagram between DHT22 and Arduino Nano ESP32

Wiring to Arduino Nano ESP32 is the same for both sensors. In orginal form, A resistor from 5K to 10K Ohms is required to keep the data line high and in order to enable the communication between the sensor and the Arduino Nano ESP32

Arduino Nano ESP32 - DHT22 Sensor Wiring

The wiring diagram between Arduino Nano ESP32 and DHT22 Temperature and humidity Sensor

This image is created using Fritzing. Click to enlarge image

Arduino Nano ESP32 - DHT22 Module Wiring

Most of DHT22 sensor modules have a built-in resistor, so you don't need to add it. it saves us some wiring or soldering works.

The wiring diagram between Arduino Nano ESP32 and DHT22 Temperature and humidity Module

This image is created using Fritzing. Click to enlarge image

Arduino Nano ESP32 Code - DHT22

/* * This Arduino Nano ESP32 code was developed by newbiely.com * * This Arduino Nano ESP32 code is made available for public use without any restriction * * For comprehensive instructions and wiring diagrams, please visit: * https://newbiely.com/tutorials/arduino-nano-esp32/arduino-nano-esp32-dht22 */ #include <DHT.h> #define DHT22_PIN D3 // The Arduino Nano ESP32 pin D31 connected to DHT22 sensor DHT dht22(DHT22_PIN, DHT22); void setup() { Serial.begin(9600); dht22.begin(); // initialize the DHT22 sensor } void loop() { // read humidity float humi = dht22.readHumidity(); // read temperature in Celsius float temperature_C = dht22.readTemperature(); // read temperature in Fahrenheit float temperature_F = dht22.readTemperature(true); // check whether the reading is successful or not if ( isnan(temperature_C) || isnan(temperature_F) || isnan(humi)) { Serial.println("Failed to read from DHT22 sensor!"); } else { Serial.print("Humidity: "); Serial.print(humi); Serial.print("%"); Serial.print(" | "); Serial.print("Temperature: "); Serial.print(temperature_C); Serial.print("°C ~ "); Serial.print(temperature_F); Serial.println("°F"); } // wait a 2 seconds between readings delay(2000); }

Detailed Instructions

To get started with Arduino Nano ESP32, follow these steps:

If you are new to Arduino Nano ESP32, refer to the tutorial on how to set up the environment for Arduino Nano ESP32 in the Arduino IDE.
Wire the components according to the provided diagram.
Connect the Arduino Nano ESP32 board to your computer using a USB cable.
Launch the Arduino IDE on your computer.
Select the Arduino Nano ESP32 board and its corresponding COM port.* Open the Library Manager by clicking on the Library Manager icon on the left navigation bar of Arduino IDE
Type “DHT” on the search box, then look for the DHT sensor library by Adafruit
Install the library by clicking on Install button.

A windows appears to ask you to install dependencies for the library
Install all dependencies for the library by clicking on Install All button.

Arduino Nano ESP32 Adafruit Unified sensor library

Copy one of the above code and open with Arduino IDE
Compile and upload code to Arduino Nano ESP32 board by clicking Upload button on Arduino IDE
Make the sensor colder or hotter. For example, putting the sensor near a hot cup of coffee
Check out the result on the Serial Monitor. It looks like the below:.

COM6

Send

Humidity: 31.00% | Temperature: 27.00°C ~ 80.60°F Humidity: 31.00% | Temperature: 27.00°C ~ 80.60°F Humidity: 31.00% | Temperature: 27.00°C ~ 80.60°F Humidity: 31.00% | Temperature: 27.00°C ~ 80.60°F Humidity: 31.00% | Temperature: 28.00°C ~ 82.40°F Humidity: 31.00% | Temperature: 28.00°C ~ 82.40°F Humidity: 31.00% | Temperature: 28.00°C ~ 82.40°F Humidity: 31.00% | Temperature: 28.00°C ~ 82.40°F Humidity: 32.00% | Temperature: 28.00°C ~ 82.40°F Humidity: 31.00% | Temperature: 29.00°C ~ 84.20°F Humidity: 32.00% | Temperature: 29.00°C ~ 84.20°F Humidity: 31.00% | Temperature: 29.00°C ~ 84.20°F

Autoscroll Show timestamp

Clear output

9600 baud

Newline

Video Tutorial

Learn More

※ OUR MESSAGES

As freelancers, We are AVAILABLE for HIRE. See how to outsource your project to us
Please feel free to share the link of this tutorial. However, Please do not use our content on any other websites. We invested a lot of effort and time to create the content, please respect our work!