Arduino Nano ESP32 - Stepper Motor
In this tutorial, we are going to learn how to use Arduino Nano ESP32 to control the stepper motor:
- How to use L298N driver to control bipolar stepper motor
- How to control the position of stepper motor
- How to control the speed of stepper motor
- How to control the direction of stepper motor
The tutorial can apply to any kind of bipolar stepper motor (4 wires). The tutorial will take NEMA 17 stepper motor as an example.
Hardware Preparation
Or you can buy the following sensor kits:
| 1 | × | DIYables Sensor Kit (30 sensors/displays) | |
| 1 | × | DIYables Sensor Kit (18 sensors/displays) |
Additionally, some of these links are for products from our own brand, DIYables.
Overview of Stepper Motor
There are two common types of stepper motors:
- Bipolar: These motors come with 4 wires.
- Unipolar: Unipolar motors can have either 5 or 6 wires. In the case of a 6-wire unipolar stepper motor, you can effectively use four out of the six wires to control it as if it were a bipolar stepper motor.
If you're specifically interested in a 5-wire unipolar stepper motor, you can refer to the tutorial titled Arduino Nano ESP32 - Control 28BYJ-48 Stepper Motor Using ULN2003 Driver.
However, this tutorial is exclusively dedicated to bipolar stepper motors.
Bipolar Stepper Motor pinout
A bipolar stepper motor has four pins, and these pins can be named differently depending on the manufacturer. Below, you'll find a table with some common pin names:
| PIN NO | Naming 1 | Naming 2 | Naming 3 |
|---|---|---|---|
| 1 | A+ | A | A |
| 2 | A- | A | C |
| 3 | B+ | B | B |
| 4 | B- | B | D |
The arrangement of pins, the names of wires, and the colors of wires can differ from one manufacturer to another. To understand how the wire colors correspond to the pin names, it's essential to consult the datasheet or user manual provided by the manufacturer. The image above illustrates the specifications of two distinct motors, each featuring its unique wire naming and wire coloring conventions.
Steps per Revolution
The motor's specification specifies the degree per step (let's call DEG_PER_STEP). Depending on the method of control, the steps per revolution (let's call STEP_PER_REVOLUTION) is calculated as the following table:
| Control method | Steps per Revolution | Real degree per step |
|---|---|---|
| Full-step | STEP_PER_REVOLUTION = 360 / DEG_PER_STEP | DEG_PER_STEP |
| Half-step | STEP_PER_REVOLUTION = (360 / DEG_PER_STEP) * 2 | DEG_PER_STEP / 2 |
| Micro-step (1/n) | STEP_PER_REVOLUTION = (360 / DEG_PER_STEP) * n | DEG_PER_STEP / n |
For example, If the motor's datasheet specifies 1.8 degree/step:
| Control method | Steps per Revolution | Real degree per step |
|---|---|---|
| Full-step | 200 steps/revolution | 1.8° |
| Half-step | 400 steps/revolution | 0.9° |
| Micro-step (1/n) | (200 * n) steps/revolution | (1.8 / n)° |
How to control a stepper motor using Arduino Nano ESP32
The Arduino Nano ESP32 can produce signals to command the stepper motor, but these signals may lack the necessary voltage and current levels that the stepper motor demands. Hence, an intermediary hardware driver is needed to bridge the gap between the Arduino Nano ESP32 and the stepper motor. This driver serves two primary functions:
- Amplifying Control Signals: It boosts the current and voltage of the control signals originating from the ESP32, ensuring that they meet the requirements of the stepper motor.
- Protecting the ESP32: Simultaneously, it shields the Arduino Nano ESP32 from the higher current and voltage levels used to power the stepper motor, preventing any potential damage.
Various hardware drivers are available for controlling stepper motors, and one commonly used option is the L298N Driver.
Overview of L298N Driver
A single L298N Driver can be used to control two DC motors or a stepper motor. In this tutorial, we learn how to use it to control the stepper motor.
L298N Driver Pinout
L298N Driver has 11 pins and three jumpers:
- VCC pin: supplies power for the motor. It can be anywhere between 5 to 35V.
- GND pin: is a common ground pin, needs to be connected to GND (0V).
- 5V pin: supplies power for L298N module. It can be supplied by 5V from Arduino Nano ESP32.
- IN1, IN2, IN3, IN4 pins: are connected to ESP32's pins to receive the control signal to control the stepper motor.
- OUT1, OUT2, OUT3, OUT4 pins: are connected to the stepper motor.
- ENA, ENB jumpers: are used to enable stepper motor. You need to keep both the ENA & ENB jumpers in place.
- 5V-EN jumper: if we keep 5V-EN jumper in place, the power for the L298N module is got from VCC, we do not need to connect anything to the 5V pin. if we remove the 5V-EN jumper, we need to supply power to the L298N module via a 5V pin
As described above, the L298N driver has two input powers:
- One for stepper motor (VCC and GND pins): from 5 to 35V.
- One for the L298N module's internal operation (5V and GND pins): from 5 to 7V. if the 5V-EN jumper is kept in place, we do not need to connect this pin to anything.
Wiring Diagram
This image is created using Fritzing. Click to enlarge image
※ NOTE THAT:
- Please keep all three jumpers on the L298N module in place (in case motor's power supply ≤ 12V)
- Order of the pins on stepper motors may vary between manufacturers. Please check the below table for correct wiring.
Wiring table between Arduino Nano ESP32 and L298N Driver
| Arduino Nano ESP32 pins | L298N pins |
|---|---|
| D5 | IN1 |
| D4 | IN2 |
| D3 | IN3 |
| D2 | IN4 |
Wiring table between L298N Driver and Stepper motor
Important!: Please do not care about the wire order of the stepper motor on the above wiring diagram image. It is just an example. The order of the pins on stepper motors may vary between manufacturers. Make sure that your wiring follows the below table.
| L298N pins | Stepper motor pins | Or | Or |
|---|---|---|---|
| OUT1 | A+ | A | A |
| OUT2 | A- | A | C |
| OUT3 | B+ | B | B |
| OUT4 | B- | B | D |
Before buying a stepper motor, we would recommend you check the check datasheet, specification, or manual of the stepper motor. Make sure that they provide the mapping between the pin's color and name. For example, This stepper motor provides the mapping as below image:
Based on that mapping, the wiring table becomes:
| L298N pins | stepper motor pins | wire color |
|---|---|---|
| OUT1 | A | black wire |
| OUT2 | C | green wire |
| OUT3 | B | red wire |
| OUT4 | D | blue wire |
※ NOTE THAT:
In all the above wiring tables between the stepper motor and L298N Driver, we can swap OUT1 with OUT2, OUT3 with OUT4. Therefore, there are more ways to do the wiring. However, if we swap them, the motors' rotation direction may be changed (clockwise to anticlockwise, and vice versa).
How to control a Stepper motor using an L298N driver.
Controlling a stepper motor is not a simple task, especially when we want to control it in a non-blocking manner. Fortunately, thanks to AccelStepper library, controlling the stepper motor becomes a piece of cake.
Arduino IDE also has a built-in Stepper library. However, We do not recommend you to use this library because:
- The library provides the blocking function. It means it blocks Arduino Nano ESP32 from doing other works while it controls the stepper motor.
- It does not have sufficient functions.
Instead, we recommend you use the AccelStepper library. This library supports:
- Acceleration
- Deceleration.
- Full-step and half-step driving.
- Multiple simultaneous steppers, with independent concurrent stepping on each stepper.
- Disadvantage: NOT support micro-step driving
How To Control the Position of Stepper Motor via L298N Driver
We can move the stepper motor to the desired position by using:
※ NOTE THAT:
The stepper.moveTo() function is non-blocking. This is a great point of the library. However, we have to pay attentions when using this function:
- Call 'stepper.run()' as frequently as possible. It should be called in the void loop() function.
- Do NOT use delay() function when motor is moving.
- Should NOT use Serial.print() and Serial.println() function when motor is moving. These functions make the stepper motor move slower.
How To Control the Speed of Stepper Motor via L298N Driver
We can control not only the speed but also acceleration and deceleration by using some simple functions.
How To Control the Direction of Stepper Motor via L298N Driver
If you do the wiring as above, the motor will rotate in:
- Clockwise direction: if we control the motor from a position to higher position (Position increment)
- Anticlockwise direction: if we control the motor from a position to lower position (Position decrement)
For example:
- If the current position is 100 and we control the motor to 200, the motor rotates in the clockwise direction
- If the current position is -200 and we control the motor to -100, the motor rotates in the clockwise direction
- If the current position is 200 and we control the motor to 100, the motor rotates in the anticlockwise direction
- If the current position is -100 and we control the motor to -200, the motor rotates in the anticlockwise direction
※ NOTE THAT:
As mentioned before, if you swap OUT1 with OUT2, or OUT3 with OUT4, the increment of the position may be anticlockwise and the decrement of the position may be clockwise.
How To Stop Stepper Motor
- The stepper motor will automatically stop after reaching the desired position.
- The stepper motor can be forced to stop immediately anytime by using stepper.stop() function.
Arduino Nano ESP32 Code - Stepper Motor Code
The below code does:
- Rotate motor one revolution in the clockwise direction
- Stop motor 5 seconds
- Rotate motor back one revolution in the anticlockwise direction
- Stop motor 5 seconds
- That process is repeated again and again
Detailed Instructions
To get started with Arduino Nano ESP32, follow these steps:
- If you are new to Arduino Nano ESP32, refer to the tutorial on how to set up the environment for Arduino Nano ESP32 in the Arduino IDE.
- Wire the components according to the provided diagram.
- Connect the Arduino Nano ESP32 board to your computer using a USB cable.
- Launch the Arduino IDE on your computer.
- Select the Arduino Nano ESP32 board and its corresponding COM port.
- Open the Library Manager by clicking on the Library Manager icon on the left navigation bar of Arduino IDE
- Search “AccelStepper”, then find the AccelStepper library by Mike McCauley
- Click Install button to install AccelStepper library.
- Copy the above code and open with Arduino IDE
- Click Upload button on Arduino IDE to upload code to Arduino Nano ESP32
- You will see:
- Stepper motor rotates one revolution in the clockwise direction
- Stepper motor stops 5 seconds
- Stepper motor rotates back one revolution in the anticlockwise direction
- Stepper motor stops 5 seconds
- The above process is run repeatedly.
- See the result on Serial Monitor
Code Explanation
Read the line-by-line explanation in comment lines of source code!