Arduino Nano - Door Sensor - LED

This tutorial instructs you how to use the Arduino Nano and door sensor to control the LED. We will learn two different applications:

Application 1 - LED is on when door is open and LED is off when door is closed. The LED state is synchronized with the door sensor's state. In detail:

Arduino Nano turns on the LED when the door is opened.
Arduino Nano turns off the LED when the door is closed.

Application 2 - The LED state is toggled each time the door is opened. More specifically:

If Arduino Nano detects that the door has been opened (the sensor state changes from LOW to HIGH), it will turn ON the LED if it's currently OFF, or turn OFF the LED if it's currently ON.
Closing the door sensor does not affect to the LED state.

Hardware Preparation

1	×	Arduino Nano
1	×	USB A to Mini-B USB cable
1	×	Door Sensor
1	×	LED
1	×	220 ohm resistor
1	×	Breadboard
1	×	Jumper Wires
1	×	(Recommended) Screw Terminal Expansion Board for Arduino Nano
1	×	(Recommended) Breakout Expansion Board for Arduino Nano
1	×	(Recommended) Power Splitter For Arduino Nano

Or you can buy the following sensor kits:

1	×	DIYables Sensor Kit (30 sensors/displays)
1	×	DIYables Sensor Kit (18 sensors/displays)

Disclosure: Some of the links provided in this section are Amazon affiliate links. We may receive a commission for any purchases made through these links at no additional cost to you.
Additionally, some of these links are for products from our own brand, DIYables.

Overview of LED and Door Sensor

If you are unfamiliar with LED and door sensor (including pinout, operation, and programming), the following tutorials can help:

Wiring Diagram

This image is created using Fritzing. Click to enlarge image

Application 1 - The LED state is in sync with the door sensor state

Arduino Nano Code

/* * This Arduino Nano code was developed by newbiely.com * * This Arduino Nano code is made available for public use without any restriction * * For comprehensive instructions and wiring diagrams, please visit: * https://newbiely.com/tutorials/arduino-nano/arduino-nano-door-sensor-led */ #define DOOR_SENSOR_PIN 2 // The Arduino Nano pin connected to the door sensor's pin #define LED_PIN 3 // The Arduino Nano pin connected to the LED int door_state; void setup() { Serial.begin(9600); // Initialize the Serial to communicate with the Serial Monitor. pinMode(DOOR_SENSOR_PIN, INPUT_PULLUP); // set arduino pin to input pull-up mode pinMode(LED_PIN, OUTPUT); // set arduino pin to output mode } void loop() { door_state = digitalRead(DOOR_SENSOR_PIN); // read state if (door_state == HIGH) { Serial.println("The door is open");; digitalWrite(LED_PIN, HIGH); // turn on LED } else { Serial.println("The door is closed"); digitalWrite(LED_PIN, LOW); // turn off LED } }

Detailed Instructions

Connect an Arduino Nano to your computer with a USB cable.
Launch the Arduino IDE, and select the correct board and port.
Copy the code and open it in the Arduino IDE.
Click the Upload button on the Arduino IDE to compile and upload the code to the Arduino Nano.

Open and close the door
Check out the change in the LED's state.

You will see that the LED state is in sync with the door sensor state.

Code Explanation

Check out the line-by-line explanation contained in the comments of the source code!

Application 2 - Door Sensor toggles LED

Arduino Nano Code - Door Sensor Toggles LED

/* * This Arduino Nano code was developed by newbiely.com * * This Arduino Nano code is made available for public use without any restriction * * For comprehensive instructions and wiring diagrams, please visit: * https://newbiely.com/tutorials/arduino-nano/arduino-nano-door-sensor-led */ #define DOOR_SENSOR_PIN 2 // The Arduino Nano pin connected to the door sensor's pin #define LED_PIN 3 // The Arduino Nano pin connected to the LED int led_state = LOW; // The current state of LED int prev_door_state; // The previous state of door sensor int door_state; // The current state of door sensor void setup() { Serial.begin(9600); // Initialize the Serial to communicate with the Serial Monitor. pinMode(DOOR_SENSOR_PIN, INPUT_PULLUP); // set arduino pin to input pull-up mode pinMode(LED_PIN, OUTPUT); // set arduino pin to output mode door_state = digitalRead(DOOR_SENSOR_PIN); } void loop() { prev_door_state = door_state; // save the last state door_state = digitalRead(DOOR_SENSOR_PIN); // read new state if (prev_door_state == HIGH && door_state == LOW) { // state change: HIGH -> LOW Serial.println("The door-closing event is detected"); // toggle state of LED led_state = !led_state; // control LED according to the toggled state digitalWrite(LED_PIN, led_state); } }

Code Explanation

You can locate the explanation in the comment lines of the Arduino Nano code above.

In the code, the expression led_state = !led_state is equal to the following code:

if(led_state == LOW) led_state = HIGH; else led_state = LOW;

Detailed Instructions

Copy the code and open it in the Arduino IDE.
Upload the code to the Arduino Nano.
Open and close the door several times.
Check out the change in the LED's state.

You will see that the LED state is toggled once each time the door is closed.

Video Tutorial

Learn More

※ OUR MESSAGES

As freelancers, We are AVAILABLE for HIRE. See how to outsource your project to us
Please feel free to share the link of this tutorial. However, Please do not use our content on any other websites. We invested a lot of effort and time to create the content, please respect our work!